HD/SD 6-inch LCD Waveform Monitor WM-3014 Instruction Manual Ver.1.00
vi Handle the liquid crystal protective panel carefully. Carefully wipe off any fingerprints or dirt on the liquid crystal protective panel with
INTRODUCTION vii Concerning problems due to the nature of liquid crystal The following minor problems may occur due to the nature of liquid crystal.
viii
1 11 CONCERNING THE WM-3014 The WM-3014 is a compact, lightweight and portable LCD waveform monitor
2 Single-action operation for selecting input channels, partial display/non-display of information, picture overlay and freeze/update using the
3 22 PARTS AND THEIR FUNCTIONS 2.1 WM-3014 front panel view and parts Fig. 2.1 WM-3014 front panel view 8 9 7 10 1112131
4 Table 2.1 Front panel parts No. Part Description of function 1 POWER switch / LED This switch is used to turn the power ON and OFF. (Its LED l
Chapter 2 PARTS AND THEIR FUNCTIONS 5 21 22 23 24 25 P1 switch P2 switch P3 switch P4 switch P5 switch Operations in modes other than the freeze m
6 2.2 WM-3014 rear panel view and parts Fig. 2.2 WM-3014 rear panel view 1 9 2 3 4 5 6 10 87 COMPOSITE IN
Chapter 2 PARTS AND THEIR FUNCTIONS 7 Table 2.2 Names of rear panel parts No. Part Description of function 1 Power socket (*1) Cannon connect
8 *2: TALLY connector (no.9 in rear panel view) Pin No. Function 1 GND 2 TALLY 2(G) 3 PRESET 1 4 PRESET 2 5 GND 6 PRESET 3 7 TALLY 1(R) 8 PRESET 4
9 33 OPERATION 3.1 Connection procedure This section describes how to connect the following to the WM-3014. (1) Connecting the power supply Check
10 3.3 Concerning the screens This section describes the screen displays of the WM-3014 and the setting procedures.
Chapter 3 OPERATION 11 No. Item Description Display modes 1 (Reference) The input reference signal is displayed here. Int denotes "Int
12 Peaking OFF OTHERS 9 R-Bright 0.0% B-Bright 0.0% Bright 0.0% G-Bright 0.0% BRIGHTNESS 5
Chapter 3 OPERATION 13 No. Item Description Display modes 1 Filter This indicates whether the filter is ON or OFF. P1, P2 2 Mono This ind
14 No. Item Description Display modes 1 YPbPr / GBR This indicates the waveform display method. W 2 Parade / Overlay This
Chapter 3 OPERATION 15 No. Item Description Display modes 1 Information This indicates the color of the characters. P1, P2
16 3.4 Operation This section describes the WM-3014 screen displays. Descriptions of each mode are given in the following sections. PICTURE1 mode
Chapter 3 OPERATION 17 3.4.1 PICTURE1 mode 3.4.1.1 Function screen 〈〈 Functions 〉〉 The input images are displayed on this screen. 〈〈 Screen 〉〉
HD/SD 6-inch LCD Waveform Monitor WM-3014 Instruction Manual 2006.8 Ver.1.00 ASTRODESIGN,Inc
18 3.4.1.2 Brightness setting screen 〈〈 Functions 〉〉 The input images are displayed, and the following image adjustments are performed on this scr
Chapter 3 OPERATION 19 3.4.1.3 Contrast setting screen 〈〈 Functions 〉〉 The input images are displayed, and the following image adjustments are pe
20 3.4.1.4 Chroma setting screen 〈〈 Functions 〉〉 The input images are displayed, and the following image adjustments are performed on this screen.
Chapter 3 OPERATION 21 [ Description of operations ] Switch Description of function FUNC switch Use this to return to the function screen. (Refer
22 3.4.1.5 Gamma setting screen 〈〈 Functions 〉〉 The input images are displayed, and the following image adjustments are performed on this screen.
Chapter 3 OPERATION 23 3.4.1.6 Other image setting screen 〈〈 Functions 〉〉 The input images are displayed, and the following image adjustments are
24 [ Description of operations ] Switch Description of function FUNC switch Use this to return to the function screen. (Refer to section 3.4.1.1.)
Chapter 3 OPERATION 25 3.4.1.7 Color setting screen 〈〈 Functions 〉〉 By holding down the OVERLAY switch in the PICTURE1 mode, the input images are
26 3.4.2 PICTUER2 mode 3.4.2.1 Normal screen 〈〈 Functions 〉〉 The input images are displayed, and the following settings can be performed. z Monoc
Chapter 3 OPERATION 27 [ Description of operations ] Switch Description of function FUNC switch No function. F1 switch Mono Use this to set mo
28 3.4.2.2 User marker setting screen 〈〈 Functions 〉〉 When the F5 switch (Marker switch) is held down in the PICTURE2 mode, the input images are d
Chapter 3 OPERATION 29 3.4.2.3 Color setting screen 〈〈 Functions 〉〉 When the OVERLAY switch is held down in the PICTURE2 mode, the input pictures
30 3.4.3 PICTURE3 mode 3.4.3.1 Regular screen 〈〈 Functions 〉〉 The input images are displayed, and the following settings can be performed. z H De
Chapter 3 OPERATION 31 3.4.3.2 Color setting screen 〈〈 Functions 〉〉 When the OVERLAY switch is held down in the PICTURE3 mode, the following sett
32 3.4.4 WAVEFORM mode 3.4.4.1 Function screen 〈〈 Functions 〉〉 The waveforms are displayed on this screen. * When composite signals are input, t
Chapter 3 OPERATION 33 3.4.4.2 DISPLAY setting screen 〈〈 Functions 〉〉 The waveforms are displayed, and the following settings can be performed on
34 3.4.4.3 SWEEP setting screen 〈〈 Functions 〉〉 The waveforms are displayed, and the following settings can be performed on this screen. z 1H, 2H
Chapter 3 OPERATION 35 [ Description of operations ] Switch Description of function FUNC switch Use this to return to the function screen. (Refer
36 3.4.4.4 GAIN/MAG setting screen 〈〈 Functions 〉〉 The waveforms are displayed, and the following settings can be performed on this screen. z Gain
Chapter 3 OPERATION 37 [ Description of operations ] Switch Description of function FUNC switch Use this to return to the function screen. (Refer
i CONTENTS CONTENTS...
38 3.4.4.5 CURSOR setting screen 〈〈 Functions 〉〉 The waveforms are displayed, and the following settings can be performed on this screen. z H and
Chapter 3 OPERATION 39 3.4.4.6 SETTING mode setting screen 〈〈 Functions 〉〉 The waveforms are displayed, and the following settings can be perform
40 [ Description of operations ] Switch Description of function FUNC switch Use this to return to the function screen. (Refer to section 3.4.4.1.)
Chapter 3 OPERATION 41 3.4.4.7 Color setting screen 〈〈 Functions 〉〉 When the OVERLAY switch is held down in the WAVEFORM mode, the following sett
42 3.4.5 VECTOR mode 3.4.5.1 Regular screen 〈〈 Functions 〉〉 The signals on the vectorscope can be displayed, and the following settings can be pe
Chapter 3 OPERATION 43 [ Description of operations ] Switch Description of function FUNC switch Use this to switch the display to the VECTOR mode
44 3.4.5.2 VECTOR mode setting screen 〈〈 Functions 〉〉 The signals on the vectorscope can be displayed, and the following settings can be performed
Chapter 3 OPERATION 45 3.4.5.3 Color setting screen 〈〈 Functions 〉〉 When the OVERLAY switch is held down in the VECTOR mode, the following settin
46 3.4.6 STATUS mode 3.4.6.1 Regular screen 〈〈 Functions 〉〉 The signals on the status can be displayed, and the following settings can be perform
Chapter 3 OPERATION 47 3.4.6.2 Color setting screen 〈〈 Functions 〉〉 When the OVERLAY switch is held down in the STATUS mode, the following settin
ii 3.4.4.5 CURSOR setting screen...38 3.4.4.6 SETTING mod
48 3.4.7 AUDIO mode 3.4.7.1 Audio level meter screen 〈〈 Functions 〉〉 z Audio levels displayed for 16 channels z Selection of headphone output
Chapter 3 OPERATION 49 3.4.7.2 Audio vector screen 〈〈 Functions 〉〉 z Left/right vector display selected for headphone output z Selection of hea
50 3.4.7.3 Color setting screen 〈〈 Functions 〉〉 When the OVERLAY switch is held down in the AUDIO mode, the following settings can be performed on
Chapter 3 OPERATION 51 [ Description of operations ] Switch Description of function FUNC switch Use this to return to the previous screen. F1 swi
52 3.4.8 Multi mode In the multi mode, the DISPLAY, OVERLAY and F1 to F5 switches do not work when the multi mode 1 screen is selected; when the m
Chapter 3 OPERATION 53 [ Description of operations ] Switch Description of function FUNC switch Use this to display the multi mode 2 screen. (Ref
54 3.4.8.2 Multi mode 2 screen 〈〈 Functions 〉〉 The input images and waveforms can be displayed simultaneously. The following settings can be perfo
Chapter 3 OPERATION 55 3.4.9 PRESET mode 〈〈 Functions 〉〉 By pressing (that is, not holding down) the P1 to P5 switches, the data stored in those
56 3.4.10 MENU mode 3.4.10.1 Regular screen 〈〈 Functions 〉〉 The signals on the menu can be displayed, and the following settings can be performed
Chapter 3 OPERATION 57 [ Description of operations ] Switch Description of function FUNC switch No function. Turning the adjustment dial Turn th
CONTENTS iii Chapter 6 MAINTENANCE AND OTHER PROCEDURES...81
58 3.4.10.2 Color setting screen 〈〈 Functions 〉〉 When the OVERLAY switch is held down in the MENU mode, the following settings can be performed on
Chapter 3 OPERATION 59 3.4.11 Compare mode 3.4.11.1 Outline 〈〈 Outline 〉〉 The compare mode is established by pressing P1, P2, P3 or P4 in the fr
60 3.4.11.2 Compare mode 1 〈〈 Outline 〉〉 In this mode, the picture screens of the freeze data and current data are superimposed onto each other, a
Chapter 3 OPERATION 61 3.4.11.3 Compare mode 2 〈〈 Outline 〉〉 In this mode, the vectorscopes of the freeze data and current data are superimposed
62 [ Description of operations ] (Regular screen) Switch Description of function FUNC switch Use this to set the display to the VECTOR mode settin
Chapter 3 OPERATION 63 3.4.11.4 Compare mode 3 〈〈 Functions 〉〉 In this mode, the waveforms of the images for the freeze data and current input da
64 3.4.11.5 Compare mode 4 〈〈 Functions 〉〉 In this mode, the freeze data and current input data are displayed simultaneously. The images are displ
65 44 MAIN SPECIFICATIONS 4.1 Input formats Format Frame Rate (Hz) ActiveLine per FrameTot al Line Per FrameLine Frequency(kHz) Samples per Activ
66 4.2 Input signal systems SDI input specification Specification HDTV BTA S-004B complied with,SMPTE 292M complied with, NRZI SDI signal SDTV
Chapter 4 MAIN SPECIFICATIONS 67 4.4 Headphones output format Maximum output 50mW ± 5% (32Ω/1kHz) Frequency response 100Hz to 20kHz (0dB to -3
iv INTRODUCTION Thank you very much for purchasing this model WM-3014 HD LCD waveform monitor. This manual contains the procedures to be followed t
68 4.5 Concerning the adjustment values Brightness The offset level of the luminance signal can be varied in the range of -50.00 to +50.00%. T
Chapter 4 MAIN SPECIFICATIONS 69 Chroma, Pb (Cb), Pr (Cr) The level of the chrominance signals can be varied in the range of 0.0 to 200.0%.
70 Precautions for chroma boost function The figure below shows the relationship between the Pb and Pr input signals and the display level when t
Chapter 4 MAIN SPECIFICATIONS 71 4.6 Concerning the 4:3 function With a resolution of 1920 × 1080 pixels An image with an area of 1440 × 108
72 Explanation of displays ••• This indicates the image. ••• This indicates the liquid crystal screen. ••• This indicates an
Chapter 4 MAIN SPECIFICATIONS 73 4.7 Concerning the audio level meter The audio level meter indicates the level as follows. Audio standards: BT
74 4.8 Settings at initialization The settings established when the WM-3014 was shipped from the factory and when they are initialized are liste
Chapter 4 MAIN SPECIFICATIONS 75 Setting item Setting/adjustment range Initial value SWEEP 1H, 2H, 1F, 2F 1H GAIN (WAVEFORM mode) ×0.03 to ×7.9
76 Setting item Setting/adjustment range Initial value Blue ON, OFF ON Red ON, OFF ON Volume 0 to 255 128 Output 1CH to 16CH L:1CHxR:2CH SDI
Chapter 4 MAIN SPECIFICATIONS 77 4.9 General specifications Table 4.1 Operating environment and ratings for WM-3014 (main unit) Operating temper
INTRODUCTION v Concerning foreign matter Do not spill liquids inside the monitor or drop inflammable objects or metal parts into it. Operating th
78 4.10 Outline drawings MADE IN JAPANSER.No ;MODEL ;DC IN 12V1 GND 4 +12VMONITOR OUTTALLYY INSDI IN CH BSDI IN CH AWAV
79 55 STANDARD AND OPTIONAL ACCESSORIES 5.1 Standard accessories WM-3014 instruction manual 1 copy AC/DC adapter 1 pc M4 screws (for attaching r
80
81 66 MAINTENANCE AND OTHER PROCEDURES When the monitor does not operate properly Symptom What is to be checked The image is not displayed prope
82
WM-3014 Instruction Manual NOTICE ● An incorrectly collated manual or a manual with missing pages will be replaced. ● All copyr
Kommentare zu diesen Handbüchern